Windster WS-38 Instrukcja Użytkownika

OPERATIONPlease read and save this guide through before using your range hood.Store the guide away in a safe place so that you will know where it is,w

4. Pick up the inner oil collector.NOTE : Reinstalling Baffle filters. Reverse the steps as removing Baffle filters.For mounting under cabinet1. After

2. After using the machine, wipes the machine by neutral detergent inorder to keep it clean and maintain the appearance with brightnessand sanitation.

10F. Completely finished .A. Remove the pre-mounted6” round duct opening.B. Put transition plate by firstinstalling on thehalf round section.(Optional

11A. Remove the pre-mounted6” round duct opening.B. Put transition plate by firstinstalling onthe half round section.(Optional)4 screwsC. Use slotted

12F. Take the pre-mountedrectangular plate.H. Insert appropriate rectangularstarting collar (optional)(2 different size)¼ ¾ (LxWxH)11¼”x3¾”x3 (LxWxH)ⓐ

1. Position the hood in place so that :2. Adjust the hood so the front is flush with the cabinet front.a. The electrical line is routed through the ap

1. Using metal brackets and screws(included), center hood ontoboard and install screw.2. Remove the hood from the board andnail the wood board onto th

1. Remove stainless Baffle filters. ( Ref.P8-H)2. Remove screws on wiring case,fish out wires through theknockout. (Fig.12)3. Mark the electrical conn

162.: Fan speed selection and fan off.A. : When the main power button is being pressed, by pressingbutton / / for desired fan speed.- slow speed- medi

Note:Care Instruction :Care Instruction :17Range hood should be turn on either before or the same time when cookingbegins. After cooking, range hood s

Table of ContentsImportant Safety Instructions ----------------------------Safety Notes -------------------------------------------------Tools and Mat

CorrectionSymptomFan are not operatable.Illuminating LED lightdoes not workA. Check power source to see if it is normal.A. Disconnect the power source

T. Parts Layout DiagramT. Parts Layout Diagram191432567891011121314151617181920

20Parts ListParts ListDescriptionHood casingAir chamberTop plate6” round vent ( )Motor housingInner vent (Rear ventilation)Motor (s)Fan (s)Oil tunnel*

NOTE : Any faults with this unit should only be attended to by a qualified technician.U. Circuit DiagramU. Circuit Diagram21Voltage : 110V/60HzPower c

V. SizeV. Size2215"11"5"9212"262-1/2"22-7/16"12”26°22-7/16”2-1/2”92°15”11”5”8-3/8”5”2°30”(36”)(42”)(48”)22-7/16”11”

What Is Not Covered By These Warranties:1) Conditions and damages resulting from a ny of the following:? Improper installation, delivery, or maintenan

Defective Products:All produc ts will be inspected, tested, and carefully packed by the manufacturerbefore shipping to customers. Products that are da

2102 N. Seaman Ave.,S. El Monte, CA 91733TEL:(626)350-1015(626)350-5215FAX:(626)350-1254© 2006-2008 Windster Hoods, Inc.Specifications subject to chan

Read and Save These InstructionsCAUTION- To reduce risk of fire and to properly exhaust air, make sureto properly exhaust air. Be sure to duct air out

WARNING- To reduce the risk of injury in the event of a range top greasefire, observe the following:A- with a close- fitting lid, cookie sheet,or meta

1. All electrical work must be done in accordance with local and/or nationalelectrical code as applicable for safety. This product must be groundedif

Drill, electric of ratchet driver, with 3/16" wood bit (for drilling starterholes and 1 ” wood bit (to drill an access holes in the cabinet orkit

1. Remove the top electricalknockout, you may plan tobring power to the rangehood either through thecabinet or through the wall(Fig.1)2. Insert a scre

1. If you want to move the electric range to make room for working on the cabinetturn off the 220 volt power for the electric range at the service ent

C. Screw the four 1" wood screws (formounting the hood) into the exactcenter of the arrow and into the keyholemounting slots marked on the cabine